Success in the oil and gas industry comes with effectively juggling four key elements: money (made or lost), risk, technical capability, and competition. Information is key to managing this process. Data sharing is the controlled process of providing information to and obtaining information from your competitors in such a manner to ensure your success (and theirs, as well). When well executed, data sharing can help one optimally find and develop highly profitable properties with minimal risk for failure. Unfortunately, poorly executed, the data sharing process can tilt the pursuit in the other direction, as well. This paper was prepared to provide the reader with an understanding of the data sharing process and how to effectively leverage information to succeed in such a competitive and technically challenging environment. There are many data sources available, with varying degrees of cost and value. A great deal of data is available for free from public sources, in a variety of formats. There is also an entire industry made up of companies that, for a fee, provide consistent methods to retrieve public data. They also provide value-added services to validate, scrub, and, sometimes, interpret the data. There are also services to find relevant information or, if necessary, to generate data. Each of these methods incurs some cost, whether it be directly financial, in terms of effort, or risk (due to reliability concerns). A great advantage of these methods is that there is no need to release valuable data to one’s competitors. The disadvantage is that a great deal of valuable information is not available via these avenues. This is where data sharing comes in, from consortia to directly sharing with potential competitors. Data sharing can be extremely valuable, not only in obtaining data but also in developing relationships that build information conduits and can lead to profitable operations that can only be pursued with a partner. While there is considerable value to this approach, there are challenges and hazards that need to be navigated. This paper describes the various methods of retrieving, purchasing, and sharing data and how to utilize data sharing as a mechanism to effectively compete in a challenging environment.

Catastrophic accidents in offshore drilling operations have greatly endangered human lives, environment and capital assets. Although risks in offshore oil and gas operations cannot be completely eliminated, a substantial amount of risks can be minimized through preventive and mitigative measures. A key aspect of the offshore drilling risk is the reliability of drilling systems. According to the World Offshore Accident Dataset and many other investigations, the overwhelming majority of disastrous accidents in offshore drilling operations were caused by equipment failures and human errors. The capabilities to predict the lifetime and provide early and effective warnings in real time are crucial to ensure reliable and safe offshore operations. The objective of this research is to mitigate offshore drilling risks by developing a scientific framework for data-driven failure prognosis for complex drilling systems operating in heterogeneous and extremely harsh environments. A novel data-driven reliability model in conjunction with a systems and economic impact analysis is developed integrating multi-source (e.g., operations and maintenance records, in-situ monitoring data) and multi-modal (e.g., lifetime data, degradation profiles) data. Numerical cases studies will be presented to demonstrate the proposed method. 
 

In a reciprocating rod lift application, production tubing failure due to metal-to-metal contact with sucker rod couplings is a common problem in the highly deviated sections of the tubing string. The coupling is forced to be the point of contact against the tubing wall, which causes high friction and excessive tubing wear during the reciprocating motion. This excessive tubing wear typically leads to a hole in the tubing wall, resulting in high workover costs for the producer.  The coupling surface hardness, roughness, and coefficient of friction between the coupling and the tubing are all directly related to the resulting tubing wear generated at the contact region.  This paper intends to show through both in-house laboratory testing and preliminary field results that applying a lower friction coating to a sucker rod coupling decreases tubing wear and increases the life of the string. 

Problem being addressed: Determining optimized Gas Injection Rate for Gas Lifted wells to maximize lift efficiency. Challenges: While Gas Lift is the most natural artificial lift method, ever-changing surface and downhole conditions cause significant inefficiencies. The changing conditions require frequent adjustments to surface-injected gas rates to maintain the most efficient lifting gradient. If the proper adjustments are not made, these inefficiencies may hinder production and increase lease operating expenses. Solution: By using Apergy’s proprietary hunting algorithm, Bloodhound, optimal gas injections rates are determined by the magnitude in the bottom hole pressure drawdown, with use of a permeant down hole gauge. Through continuous and proportional rate adjustment, the Bloodhound algorithm learns from previous set point deltas and tests against the inferred optimal rate, as well as changing conditions. Results: In under-injection scenarios, Bloodhound can accelerate the recovery of oil by up to 10 percent, regardless of the well’s position on its natural decline. In over-injecting scenarios, wells can maintain oil production rates while using up to 50 percent lift gas. Both results can be successfully achieved with few engineering hours, manually calculating or modeling well performance curves to determine inferred optimal rate. 
 

A hydrodynamic analysis for different rod guide designs simulating downhole fluid conditions was made using computational fluid dynamics (CFD) analysis, which is widely used for solving the partial differential equations of fluid motion by discrete approximation.  A particular turbulence kinetic energy graphic for each guide sample was created and compared to each other. The results shows a significant difference between the samples and the new rod guide design with conclusive proof of a better hydrodynamic performance. 

Dog Leg Severity (DLS) had been used for many decades as recommendations to try to drill oil and gas wells and provide "trouble free" operating conditions. Many of these recommendations were historically based on vertical, shallow (<5000 ft.) deep wells. But as wells continued to be drilled deeper, the recommendations were still applied. With the current drilling and operating practices of deviated and/or horizontal wells, these recommendations may no longer be applicable. Additionally, the deviation measurement interval (degrees/100 ft.) also may no longer be accurate when trying to match downhole problems using existing rod string design software. Furthermore, as wells have become deeper and many now also exclusively are drilled as deviated/ horizontal, side loading (SL) may be a more appropriate condition to be used to determine problems. This paper will review the historic DLS recommendations, provide insight on deviation measurement interval, discuss the importance of SL, and provide new recommendations for drilling wells that should provide better, longer term, less problematic operating wells.

In 2017 and 2018 Oxy EOR conducted a series of RCFA schools. As part of these schools, information was gathered on the range of equipment replacement for failure types. In 2018, a cross functional team of experienced stakeholders vetted this information and compiled a list of equipment replacement guidelines. This paper will share these guidelines. 

The Midland Basin teaches a hard lesson in drilling harder rock. SM Energy first drilled there in 2008 before launching a successful horizontal drilling campaign in 2013. This work focuses on a successful application of the limiter redesign process supported with downhole sensors. Whirl suppression generates ROP performance improvements. This objective is complicated with a coupling to stick slip in hard rock applications. High WOB and therefore high torque tends to excite stick slip. Torque oscillations start, speed oscillations follow, and result in inconsistent DOC. Bit forensics on large wear flat shoulder cutter wear and delamination indicate high speed, friction, and heat damage under these conditions. This problem is explored in depth across the interbedded intermediate section of three pilot wells within the operator’s southern Midland Basin acreage. All three wells were drilled in a single bit run to TD and successfully cased and cemented by design. Three high frequency sensors recording at 100 Hz were installed in each BHA – one located in the bit, above the drilling motor, and at the drill collars. High frequency surface measurements were successfully tied to subsurface sensor observations. Good wellbore trajectory design, high ROP, and low planned dog leg severity positively contributed to weight transfer exceeding +97% based on WOB measurements in the BHA. Autodriller setpoint control and tuning unlocked ROP gains between 20-40% in the shallow hole section. MSE is reintroduced. Its practical value in baseline drilling surveillance and benchmarking is confirmed. The first well is treated as the control in the project. The trial starts with the common bit and BHA for the area with planned parameter step tests performed in each significant formation group. The second and third wells repeat the same workflow with progressive BHA changes to a single component. Depth of cut control is designed and utilized successfully on these wells to reduce torque oscillation. Roller reamers implemented on the final well act as a low torque stabilizer to increase useful torque at the bit. Torque stabilization and minimizations strategies must be paired with sufficient drill string stiffness to maximize performance impact in high WOB applications. The drilling performance initiative outlined in this paper is meant to be accessible to all drill teams and a call to action to redesign problems to the economic limit, forever. 
 

With the increase in the number of horizontal wells drilled in the past 15 years, the technology for predicting downhole conditions and troubleshooting problem wells has not kept up with the increased complexity of these deeper and deviated wellbores. The systems in use are no longer accurate or sensitive enough to determine what is causing the problem(s) resulting in shorter meantime between failure and higher workover cost to the operators. To unravel the mystery we introduce the Downhole Sucker Rod Sensor which measures what is happening downhole and enables the customer a systematic approach to troubleshooting and therefore reducing the number of failures while providing a method for measuring the effectiveness of new and existing technologies. These sensors can be strategically placed anywhere in the rodstring and collect high-resolution measured data for pressure, temperature, torque, compression, velocity and position. In addition to generating a high resolution measured downhole DynaCard that can distinguish sync issues with different strokes per minute (SPM). The data is used to uncover issues with string wear i.e. alignment or sync issues, friction, pump and tubing issues as well as calculated values for specific gravity, pump fillage, and pump intake pressure. The main objectives are summarized as follows: o Comparing actual Downhole DynaCard measurements to the Surface and the Predicted Cards o Maximizing reservoir drainage and production optimization o Identifying, isolating and optimizing mechanical issues in problem wells o Measuring the impact of new and existing technologies (such as guides, friction reducers, …) and their effectiveness in extending the service life of the SR system. o Verify if rod guides, friction reducers… are adding value and not just cost! Vision: o Utilize sucker rod sensor(s) on problem wells and convey lessons learned to other wells. o Improve the software systems currently calculating downhole dynagraphs. o Improve the accuracy of (surface) software calculations which will yield improvements for a large number of unconventional wells. o Provide our Customer’s with a competitive advantage. 
 

The purpose of this project is to conduct a Dynamic Filtration Test to Investigate the Effect of Preformed Particle Gels (PPGs) on Un-swept, Low-Permeable Zones/Areas. A filtration test is a simple means of evaluating formation damage. This work use schematically dynamic filtration test experiment design apparatus to carry out the various filtration test experiments. It use different core samples, various brine concentration, and various gel types.  The permeability   of each sandstone core samples is calculated before and after the filtration test. Experiments are still being observed.  The objective of this study is to find methods that minimized the damage caused by PPGs on un-swept, low-permeable zones/areas, thus improving PPG treatment efficiency. This approach will identify the best properties of the PPGs, which can neither penetrate conventional solid rocks nor form cakes on the rocks’ surface. 
 

Friction reducer is a hydraulic fracturing fluid additive meant to lower costs by decreasing the friction pressure in tubulars during pumping operations. High viscosity friction reducers (HVFRs) have become increasingly popular in well stimulation applications in lieu of conventional slick water fluid systems involving linear and cross-linked gels. However, various factors must be considered when assessing the effectiveness of using HVFRs under certain frac operation conditions. This paper aims to evaluate how effective of a solution HVFRs are while determining the optimal operating conditions for this additive.

Black Mamba Rod Lift’s helical centralizer stabilizes the rod string during pumping chaos. Chaos is understood as sucker rod buckling and negative loading (compression), which is impossible to eliminate in beam lift wells. The source of compression is often from nature (gas interference, fluid pound, gas pound) but can be operator induced (seating the pump, pump tagging), or compression as part of the pumping method and operation (pump friction, fluid load transition). When compression occurs on standard slick or guided sucker rod, rods experience bending moments, or focused points of high stress leading to micro-fractures which propagate and lead to rod parts. Multiple operators big and small have tested and validated Black Mamba’s system design. By April 2022, we will have had product tested and deployed for nearly 24 months. Operators elect to use Black Mamba for standard guide replacement, but most often opt for Complete, Predictable, End-to-End Rod Control (7 Black Mamba guides per rod), eliminating instability and providing a drastic increase in rod string reliability and rod string life, increasing MTF dramatically. The implementation of rod string stability is most often found at the bottom of the rod string where compression is most prevalent, working upward. Often 3/4" rods have been removed from system and string design due to their low AMOI and increased tendency for buckling. With constant centralization, 3/4" rods take compression and never buckle, following tubing exactly. Sinker Bar replacement is common in deviated horizontals, with the industry transitioning to guided 1” or 7/8” rod body with 3/4" pin connection (reduced coupling diameter allows for extended guide life). This product offering is provided to industry by multiple manufacturers, Black Mamba doing so in Permian, Bakken, Mid-Con. Utilizing 7/8” Slim Hole Couplings (with proper derating) is a good idea for extending rod guide life and extending the time-to-first-contact between coupling and tubing. 1” Slim Hole Couplings are so large they practically render rod guides useless for 1” rod body with 1” pin connection. We discourage the use of standard 1” pin connections when possible. Hybrid sucker rod products are available and actively promoted – 1” HA/HS rod with 7/8” connection reduces coupling diameter, maintains pin-connection strength, and will extend time-to-first-contact between coupling and tubing. Designing rod strings with chaos expected is an ideal method for ensuring the rod string is buckle-proof and ready for any source of chaos, operationally driven or nature driven. Compression Control Rod String Design considers all drivers of instability; the rod string can operate without bending moments, preventing a driving force of pre-mature sucker rod fatigue. Black Mamba’s installations have increased habitual failures by 6x (last 8 failures were at 3 months each), allows operators to pump 192” stroke units at 10 SPM reliably, and removes all guess-work out of string design. Product will have been deployed for nearly 2 years across the world in a variety of pumping conditions. 

There is a growing need for energy throughout the world and this increase in demand for energy has now also put a strain on the current sources of energy. In the process of oil/gas production, there are large amounts of water released into the atmosphere as well as into the ground or soil. This water contains chemicals such as Sulphur and Nitrogen oxides, Bitumen, Calcium, Base oil, and Sodium. It is commonly referred to as “wastewater” and is disposed of. The goal of this project is to investigate the possibility of acquiring energy from this wastewater. This is can be done by using various types of soils and water. Various mixtures were created using soils mixed with different percentages of clay and water with varying salinity. A small source of electricity was then applied to the saltwater mud to provide a voltage to the experiment. The chemicals in the mud are then expected to amplify the input voltage and create enough energy to power electrical devices. To prove this, a bulb or small fan will be connected to the mud via an electrode. It was found that clay soil produced more energy than sandy soil. Also, an increase in water volume would dilute the mixture and this would slow down the transfer of energy in the mud. The results of this work can be useful for the environment and the decreasing energy sources.

One of the largest lease operating expenses is electrical cost. Only a small portion of electrical cost is value-added conversion of electricity to fluid lifting power. The rest is lost to downhole friction, fluid flow friction, pumping unit, and electrical to mechanical power conversion inefficiencies.  Overall “line to fluid” system efficiency will typically range from 20% to 40%. Some cases will be as low as 10%.

Some of those energy losses are inevitable.  Some can be reduced through improved operation and controls. This paper will present power studies of various control schemes on actual wells, highlighting the best solutions for reducing power consumption. 

The study will examine: line starters with timers, line starters with pump off controllers, pump off controllers with variable speed drives and advanced embedded controllers. Electrical average voltage(V), power factor, maximum current(A), average current(A), total apparent power(KVA), total reactive power(KVAR) and total real power(KW) will be show for each variation. Apparent costs and ROI of implementing and/or changing to a new control system will be presented.    

The use of martensitic alloys in sucker rod applications has several significant advantages over ferritic-pearlitic alloys. Processing differences in making the different microstructures will be discussed, along with the resulting property and performance differences. An evaluation of the guidelines for optimal strength in various corrosive environments will be provided. Studies on the fatigue performance of martensitic and ferritic steels will be presented.
 

In 2016, a recommendation was made in EOR to begin utilizing Grade “C” when replacing rods in San Andres wells or wells less than 5,000’ deep. The advantage of the Grade “C” rods believed to be better corrosion resistance, tubing leak reduction, and lower material cost. It was also recommended that “T” coupling be considered as an alternative to Spray Metal (“SM”) couplings as they are softer and should fail preferentially to the tubing. As with any technology that is new to the field in question there is concern about wide spread use until sufficient data is gathered on a smaller subset of wells to prove up the concept. As failure frequency is a key metric when evaluating artificial lift performance, and it can take several years to develop sufficient data, an analysis method needed to be utilized to track the equipment performance over a shorter duration so that use can be expanded as early as possible. This was accomplished by developing statistical data for sucker rod and coupling installations and failures over a specific time period comparing the failure rate of the “C” rods and “T” couplings versus the “KD” rods and “SM” couplings that are typically run. The analysis showed that the “C” grade rods and “SM” couplings were not showing an increased failure rate and therefore provided support to start expanding their use in EOR, which should result in significant cost savings. To further understand the corrosion differences between C-Rods and KD-Rods corrosion coupons were constructed from sections of actual rods and placed in several wells of varying characteristics. This paper will also present the findings from this corrosion test, which is currently nearing completion. 

Different types of forces NOT accounted for by the wave equation are 1) mechanical friction, 2) piston force acting on the polished rod due to tubing back pressure and 3) true vertical rod weight.  Mechanical friction will be discussed from 1) over-tight stuffing box, 2) down hole sticking due to a severe dogleg in the wellbore profile and 3) friction from paraffin along a section of the rod string.  The application of these external mechanical forces acting on the rod string impacts measured surface loads, down hole stroke length and plunger velocity, plus the calculated rod loading at the pump or other locations in the rod string.   
Damping coefficients are used to subtract out fluid damping as a function of velocity along the rod string using the wave equation.  Unaccounted for mechanical friction cannot be modeled by adjusting the damping factors in the wave equation.  Mechanical friction impacts both the shape of the pump card and the measured surface dynamometer card loads versus position and, as friction on the rods goes up then the surface load range also changes.  Field measured dynamometer data will be used to show examples of these different types of forces NOT accounted for by the wave equation
 

The objective of this paper is to share insights on mitigating sucker rod corrosion damage in vertical, horizontal and deviated wells with aggressive corrosive conditions such as H2S and CO2, particularly those with histories of corrosion-related rod/tubing failures.

Corrosion is a common problem in production operations, accounting for two-thirds of all rod string failures and costing billions annually to remediate, according to NACE International. This paper presents the development and initial field application results of a continuously applied metallic coating that actively participates in the electrochemical aspects of corrosion in carbon and low-alloy steels. Moreover, the solution protects uncoated segments of rod and other steel components in the wellbore while reducing abrasion by enhancing friction properties compared to bare steel.

The authors outline the key properties and characteristics of this coating, including evaluating its performance relative traditional corrosion protection measures such as barrier coatings. Rather than acting as a barrier layer, the metallic coating actively protects against corrosion and has inherent chemical properties that self-heal surface scratches and abrasions. This is particularly valuable in horizontal and directional wells with high dog leg severities and sideloading forces that contribute to rod/tubing abrasion.

Results are presented from laboratory testing as well as initial trial applications in wells with histories of rod failures due to corrosion, typically requiring interventions with workover rigs. In one such trial, the metallic coating was applied to a coiled rod string installed in a high-CO2 content well on progressing cavity pump. The coated coiled rod string was installed in January 2019. Ater five months of service, the coated string was pulled to inspect its condition. The examination revealed that the rod was unaffected by corrosion. A second inspection after nine months found evidence of rod string wear but no corrosion damage. The well has been in continuous operation for 35 months (and counting), more than doubling the average run time before installing coated coiled rod.

The novelty of this approach is the application of an advanced materials science coating to extend rod string service life in corrosive environments through active protection. In addition, it requires no special handling or installation equipment, and the metallic material allows rod strings to be recycled (eliminating potential environmental and downstream damage risks associated with barrier coatings).

As supported by lab and field case study data, the results of deploying this method include increased production uptime, reduced workover frequencies and associated remediation costs, and lower overall LOE and lifting cost per barrel of oil produced. 
 

To increase recovery rates – the greatest challenge facing the industry – operators must not only look to step-change technologies, but improvements to existing technology. Even incremental increases in recovery rates can impact economics when multiplied across numerous wells. For example, approximately two-thirds of onshore wells use beam operated pump jacks with reciprocating rod pumps. Our objective was to improve the efficiency and reliability of sucker pumps by engineering a new ball valve insert.  Prototype testing demonstrated that the lowest pressure drop was provided by an insert design with the tangent angle equal to Pi (3.14, π), as it forced the fluid into a vortex spin. Based on a number of flow rates (including two phase flow) the TangentFlow Insert decreased pressure drop by 40% on average resulting in 58% more flow than the bar-bottom inserts. In addition, compared to the bar-bottom inserts, which produced significant ball chatter, the TangentFlow Insert had a consistently low decibel reading with increasing flow rates, as the ball remained stationary. This results in reduced gas breakout, which in turn further reduces pressure drop, fluid pound and pump damage.  One-year field results from 50 wells in the Red River reservoir of Montana and North Dakota demonstrate that the TangentFlow Insert reduced pressure drop across both the standing and traveling valves to increase average surface flow by 8%. Considering the average water to oil ratio in the area, this provides an additional 3.1 bbl/day/well. This increase applied over 50 wells translates to approximately 54,603 bbl/year, or $3.33MM in revenue at current oil prices.  The design of the TangentFlow Insert improves the efficiency and reliability of sucker rod pumps by minimizing the effects of pressure drop, gas breakout, solids accumulation (wax), casing wear and ball wear, which together improve pump efficiency and production flow. Because the design enables the ball to remain stationary, smaller and lighter balls can be used, allowing for higher flowback solids and reduced cage wear, respectively. The TangentFlow Insert is manufactured to replace conventional bar-bottom inserts without needing to change out the entire pump assembly, making them applicable to 90% of pumps presently used in the industry.

Decline Curves Analysis commonly ordinarily applied to evaluate the original hydrocarbon in place, hydrocarbon reserves, and forecasting future production performance. The Decline Curves Analysis development was presented by Johnson and Bollens in (1928) and later on (1945) which is called "loss-ratio". Many discussions of the mathematical relationship between the past time, production rate, and the cumulative production depend on the decline rate. Decline Curve Analysis is a technique which might be stratified for a single well or whole reservoir by either production engineer or reservoir engineer. In oil industry, remaining reserves are the substantial target. The objective of this study is to determine and clear estimation of a reservoir performance in Libyan Oilfields by using Decline Curves Analysis and estimate the reservoir life. Also, in this work we simulate the production operation data to find out the better matching of forecasting results and the economic impact of the selected reservoir. This research is an attempt to determine one of Libyan reservoir performance and determine which one of the three classifications of the Decline Curves are Exponential, Hyperbolic, and/or Harmonic by using one of the most widespread important reliable methods to estimate the depletion of reservoir pressure with the consideration of the method limitations, the changes in the facilities downstream, and hydrocarbons production rate.

Horizontal wells are the largest capital investments made in the Permian and return on investment is essential. This project was developed to analyze the sustainability of gas lift as final form of artificial lift for unconventional horizontal wells. A pilot to run gas lift equipment deep into the lateral was developed, which involved meticulous candidate and downhole equipment selection. Two horizontal wells were selected, and deep gas lift was installed far into the lateral. 

How and where ground wires are connected determines the runtime and successful withstanding of switching and lightning surges. This is extremely evident with lightning protection of electric submersible pumps (ESP).  Electric surge suppressors on the same ground wire can and will interact bidirectionally in a lightning storm. Instances of ESP failures due to improperly installed surge suppression are not uncommon.  Understandably the value of surge suppression has been questioned.  This paper proposes separate ground wires for each surge device with all wires bonded together at the wellhead.  Justification for this is derived from multiple engineering reports on wellsite electrical installations, electrical theory and reported extended ESP run-life.

The purpose of this paper is to discuss the history of different gas lift design methods and the theory behind a new design method.  In January 2019, Production Lift Companies and Concho Resources ran a new gas lift design method in two unconventional wells in the Permian Basin.  This new method is designed to exploit the initial high bottom hole pressure in unconventional wells to produce higher rates that, before now, were only possible with an ESP.  This life of well design will also follow the well’s decline and efficiently produce the well at lower rates.  When completed correctly, the well can be switched to PAGL, Plunger Lift or GAPL without pulling the tubing.  

The traditional gas lift design method for unconventional wells is to run unloading valves until you reach a minimum spacing of 500’ (Fig. 1) and then continue the 500’ spacing to the packer.  The 500’ spacing was adopted by the industry in the late 80’s as “Best Practice” and has remained the standard today. 
 

Since its’ introduction to the unconventional oil and gas realm in 2018, Single Point High Pressure Gas Lift (referred to as HPGL going forward) has emerged as one of the top artificial lift choices for operators in the Permian and Anadarko basins. It has become a proven technology with over 1,250 applications to date as more operators are choosing it as their primary form of artificial lift for their unconventional assets. Its ability to achieve sustained high fluid rates as well as having a high sand and gas tolerance makes it the most versatile form of artificial lift offered in today’s market. HPGL is not a new concept having been discussed in SPE 14347. (Dickens, 1988) The concept was revitalized in SPE 187443 (Elmer, Elmer, & Harms, 2017) by which the authors of this paper emphasized its’ application for horizontal wells though at the time the needed compressor technology was not widely available to the market. This has changed as compression service companies have begun offering compressors designed to achieve the high discharge pressures needed to initially unload wells. This has led to a surge in HPGL applications as operators are looking to maintain the high output capabilities of ESPs with the benefits of gas lift. Gas lift is a naturally flowing process; therefore, it is important to understand the pressure drop across the entire system to achieve the desirable outcome. There are many components along the flow path from reservoir to sales that affect this pressure drop. HPGL has re-emphasized the importance of Nodal Analysis, and the understanding thereof, to production engineers. Proper design and installation of each node can drastically sway your well’s performance capabilities therefore proper modeling must be conducted to ensure the desired outcome is achieved. In this paper we will demonstrate the HPGL design method used today to ensure optimal output will be achieved. 

Managing extensive Electrical Submersible Pump (ESP) operations and evaluating their performance can be a challenging task, especially in unconventional reservoirs. Varied operational environments, expansive geographical areas, large ESP populations, different declination patterns, diverse fluid properties and well designs and different service providers are some of the complications that operators face every day. Many companies measure the success of any artificial lift project focus on simple run life statistics as the central key performance indicator; however, these types of statistics may not always be enough in providing significant information to decision makers. It is vital to the success of any project to establish a performance evaluation structure that can effectively capture deficiencies and highlight potential improvements. Survivability curves are the result of the statistical model based on Kaplan-Meier analysis, which was originally created to measure the fraction of subjects living for a certain amount of time after treatment in clinical trials, so similar methodology was deployed to analyze an important dataset of ESPs to deeper understand by factoring and comparing elements which influence ESP run life, showing results that are easier to understand and represent real value to operators on several areas as safety, engineering, reliability and operations. As a result, from this comprehensive study jointly initiated between an oil operator and ESP vendor, corrective actions were taken that drive improvements in all ESP aspects, which can be seen not only in today’s KPIs, also influence future artificial lift projects. Being able to draw conclusions about the expect runtime can be used to drawn insight on find areas where efforts should be focused to improve ESP reliability, find where ESPs can be best utilized to improve field performance, and identify opportunities to reduce workover cost. Similar analysis can be done to visualize ESP runlife improvement over time, compare different ESP technologies, and find expected runtimes by completion design or producing formation. The values of insights gained from statistical analysis can be gotten from any field of ESPs to aid in making better oilfield business decisions.