A case study has been conducted on Red Fork formation wells with bottomhole temperatures ranging from 225 degrees -250 degrees Fahrenheit. The fracturing applications and techniques in this area had historically provided lower than expected post-treatment productivity and a rapid decline rate, .suggesting that the fracture conductivity were less than optimum. Joint efforts of the operator and service company, utilizing state-of-the-art fluids, breakers, and design methodologies, were employed to optimize well productivity. The case histories of hydraulic fracturing treatments and subsequent production performance of five offset wells are analyzed and presented. Average incremental production rates were significantly improved through application of the new technologies, clearly demonstrating the effectiveness of the modifications.

Many of the benefits of the Ultra-High-Slip motor can be realized by its installation under the exact same conditions as that of the Nema D motor. However, to maximize the system efficiency and minimize operating cost, some changes may be required to optimize the Ultra-High-Slip system. The amount of effort required to optimize your installation will depend upon the particular well. In this paper, we will be discussing three well tests. All of them were conducted in 1985, Andrews County, Texas, for two different operators and on three different wells.

A field demonstration of the application of the bottom hole pressure data, as received from Real Time Diagnostics" wireless pressure transmission system, improved the efficiency of PanCanadian Petroleum Limited's 8A-19-38-Ol-W4m well in the North Bodo field of northeast Alberta, Canada. An illustration of servicing a typical North Bodo slant well on a pad of wells is shown in Figure 1. The Telemetry Acquisition Tool (TAS device, developed by Real Time Diagnostics (RTD), was installed in the production tubing below the producing zone perforations, where it was able to measure and accurately transmit bottom hole production pressures and temperatures of the well's producing horizon to the surface. The real time pressure data was relayed into a voltage loop and a surface computer which contained software designed to output an analog process signal. This signal was then sent to the Wermac Electric Limited's Variable Frequency Drive (VFD), which controls the speed and torque of the electric motor powering the bottom hole progressive cavity pump (PCP) system. PanCanadian was able to both increase the oil production and decrease the lifting costs per barrel by utilizing the actual bottom hole pressure response of the reservoir fluids flowing into the wellbore to optimize the daily rate of production.

The objective of this project is to use data mining to analyze well completion data to determine if trends or interesting patterns exist between well completion and stimulation methods and subsequent production. While a multitude of completion and stimulation techniques exist there are few objective, systematic examinations of their relative utility. A 370 well subset of basin Dakota wells drilled during 1994-2004 was examined to determine the feasibility of this concept with 58 additional wells drilled during 2004-2006 used for testing. Comparison of companies showed statistically significant differences in average production which could not be explained resolved by studies of land position via K-means clustering. Data mining was able to determine variances in first years gas production based on fracture fluid gallons, fracture fluid type, fracture interval thickness and sand lbs. A forward model was generated that could accurately estimate first years gas production based on these input parameters

This paper chronicles efforts to extend batch treatments using hydrocarbon-solvent solutions of corrosion inhibitor. Inhibitors were developed in the laboratory using parameters felt to be important for this endeavor. That is, good high inhibitor concentration inhibition, good reduced-inhibitor inhibition, and intermediate brine dispersibility. Field- testing proved these inhibitors to be effective during the extended intervals.

This paper describes a downhole separation technique that diverts the formation fluids into the basing annulus near the top of the downhole separator so that the liquids and gas can separate by gravity. A seating nipple is positioned at the bottom of the separator that is within inches of the liquids that exist in the casing annulus surrounding the gas separator to obtain unobstructed liquid flow into the pump inlet and result in higher pump fillage.
The separator design is used with a conventional packer, or a special pack-off assembly consisting of elastomer rings on a tube positioned between the separator and the tubing anchor below the separator, or a packer with tail pipe when the pump is set a considerable distance above the formation.
Two conditions affect pump fillage that can severely reduce pump displacement. A recent complicating factor that must be considered when evaluating gas separator performance is the recent use of high clearance plungers in the pumps. Large plunger clearances for sand problems are common in some areas that result in a pump plunger leakage of 50% the pump capacity, so the pump appears to be full or almost full when actually the liquid in the pump is circulated liquid that is bypassing the plunger and not new liquid being drawn into the pump chamber. The second condition is the lack of separation of free gas from liquid as the formation liquid enters the pump inlet.
The paper describes gas separation techniques and presents field data on several types of downhole gas separators.

A method is presented for optimizing roller cone bit hydraulics programs to provide minimum cost per foot drilled. The method differs from traditional optimization techniques in that optimum pump operating conditions are determined rather than being arbitrarily imposed as a constraint on the optimization process. The method considers rate of penetration (ROP) response to increased bit hydraulic horsepower (BHHP) as well as increased fuel and pump maintenance costs to provide increased BHHP. Optimum conditions may be determined through a parametric analysis or by imposing simple relationships between pump fuel and maintenance costs and ROP response to increased BHHP. Full scale laboratory drilling data under various overbalance pressure conditions are presented to demonstrate the relationship between ROP and BHHP. Laboratory and field results with blanked nozzles and asymmetric three nozzle configurations are also presented.

The Glorieta, Upper Paddock, and Lower Paddock formations were unitized in the Vacuum Field (S.E. New Mexico) by Texaco in 1992 creating the Vacuum Glorieta West Unit. A technical committee made up of working interest owners was formed to determine operational matters for the newly formed unit. The technical committee determined that the Upper and Lower Paddock intervals contained the more prolific productive capacity and provided the most suitable median for waterflooding. Consequently, unit wide water injection in those intervals commenced late that same year. Almost immediately water breakthrough occurred in the northern area of the field and in selective areas of the southern portion of the field. Unit production showed an immediate increase in unit water production accompanied by an actual decrease in unit oil production at the commencement of the waterflood. From this point forward the water/oil ratio (WOR) became the major driver of economic limit for the VGWU. It was not until the first quarter of 1994 that the Vacuum Glorieta Unit saw its first positive response to injected water, considerably after the anticipated time frame.

Tracing the fall of the plunger down the tubing can be used to optimize the operation of plunger lifted wells. On plunger lifted wells an acoustic liquid level instrument can be used to collect a series of liquid level shots down the tubing. These measurements are used to monitor the position of the plunger, as the plunger falls down the tubing during the time period the controller has closed the surface valves and the well is shut-in. The collected data is used to determine the 1) fall velocity of the plunger and 2) time for the plunger to fall to liquid. By accurately measuring the plunger fall velocity with an acoustic liquid level instrument, then the minimum shut-in time for the plunger lift installation can be determined. The plunger trace measurements will ensure that the plunger has reached the liquid at the bottom of the tubing by the end of the shut-in period. Setting the well's controller to have the shortest possible shut-in time period can maximize oil and gas production from plunger lift installations.

Many factors are involved when selecting the most cost effective artificial lift system. This paper will discuss the advantages of The DynaPump Intelligent Long Stroke Hydraulic Pumping System compared to other artificial lift systems. This system has characteristics that allow for operation at much slower strokes per minute greatly reducing tubing and sucker rod wear while retaining the ability to produce at greater volumes from deeper depths than conventional beam pumping units. This system also has features that provide superior efficiency and flexibility at any rate and depth compared to other artificial lift methods. This study compares electrical efficiency, well intervention costs, production optimization, adaptability to changing well conditions, ability to operate in harsh well conditions, and overall environmental impact between various artificial lift methods. Included are actual operating parameters and runtime comparisons. The conclusions will aid in the selection of present and future artificial lift system requirements.

BP Permian's Sprabeny production consists of 400 rod pumped wells located primarily in Midland, Martin, and Glasscock Counties. Of these, the Spraberry Core Production Area located in Glasscock County includes 80 wells, which have been producing for 30+ years. Development of the Wildfire Production Area in Midland and Martin Counties began in 1996. Wells in both areas are typically completed to about 9500" through the Sprabeny, Dean, and Wolfcamp formations. Pump depths fluctuate from 7600" to 9700" through the field. A variety of operating challenges have been encountered and worked through over the years to optimize profitability. The purpose of this paper is to discuss the teamwork and technology utilized in resolving these challenges.

Paraffin wax treatment in the Spraberry has been around since development began in the 50"s. Hot oiling and hot water have been the method of choice for many years. Chemical treatment and a combination of chemical with hot oil or water have also been alternate methods. The purpose of this paper is not to determine the best method or methods, but to attempt to define and extend the frequency of the treatment necessary to control the paraffin wax. Current treating schedules are 30, 45, 60 and 90 day. Ten wells from the Spraberry were selected for this project for monitoring via a SCADA system to establish an optimized scheduling program.

Proper design of high-volume pumping systems is essential in waterflood operations. An analysis of all the problems hampering efficient sucker rod pumping systems is necessary to arrive at the best design. Techniques of sucker rod selection, unit selection utilizing dynamometer analysis, permissible load diagrams, etc., will be discussed with a correlation of all components composing the complete high-volume sucker rod system

Intermittent gas lift is a cyclic operation where the wellbore fluids are produced in individual piston-type slugs. A design technique was developed for practical application in a South American oil field to produce fast depleting solution gas reservoirs. The design principle is based on controlled valve loading and is not affected by tubing size, thereby eliminating diminishing valve spacing with increased valve depth. An advantage of this type design is that it eliminates the possibility of not being able to work to bottom valve because of improper design. In most cases, especially in wells that have a low productive capacity, less gas lift valves can be utilized for unloading to the operating depth. Although proper gas lift design is the basis for any good intermittent gas lift operation, it is essential that the field personnel have a working knowledge of gas cost, usage and well operation. A simple trial and error testing procedure that can be used by field personnel to determine when a well is producing at a the maximum fluid rate for the minimum required lift gas usage, is a plot of producing rate versus the volume of gas injected per day. The point on the curve where the maximum fluid rate is attained with the least volume of gas injected should be the optimum intermittent gas lift operation. Therefore, optimum oil production by intermittent gas lift is a function of proper design and operation.

The importance of properly diverting stimulation treatments was recognized as early as the 1930"s. However, each new technique or material developed has carried with it limitations in applicability. It has become evident that a universally effective diverting agent is unlikely. This paper will deal almost exclusively with recent Shell Oil Company experience in the use of "solid" diverting agents in the fracture treatments. The popularity of these materials is a measure of their effectiveness.

A basic approach to the correct installation, operation and maintenance of orifice meters as used in oil and gas production. Orifice plate sizing will be demonstrated.

This paper discusses detailed aspects of organization of and operating agreements for cooperative salt water disposal systems.

The subject matter of this paper will describe organoborate fluid systems in combination with guar specific enzyme breakers. Their application, and how they were used to improve production in the Grayburg-Jackson field of SE New Mexico. Furthermore, the paper will discuss the completion objectives in the Grayburg-Jackson field as they relate to stimulation treatments and explain how wells were normalized for the purpose of this study. Finally, production results will be examined to compare organoborate/guar specific enzyme breaker combinations verses monoborate fluid systems with non-specific breakers.

Understanding of the near wellbore stress distribution is critical to implement effective fracturing strategies. Reservoir quality variations, mixed lithologies with plastic behavior will alter the near wellbore stress distribution reducing the compressive stress of the rock. Thus, constant stress gradients (0.1 psi/ft.) are misleading and rock mechanical properties measurements may prove to be of extreme importance. This work discusses the development of criteria for orienting perforating/fracturing strategies. We present, an improved completions methodology that couples a systematic and enhanced geomechanical reservoir characterization with effective fracture placement and increased production results. Case-specific examples demonstrate the advantages of using detailed stress profiles and accurate reservoir description as key components of a GeoMechanical Model. Orientated Perforation strategies are suggested to address different and complex issues; multiple fractures, near-wellbore tortuosity, maximum proppant concentration, vertical coverage, natural fractures, tortuosity and erosional effects, with subsequent impact on improved reservoir performance and well deliverability. Net pressure matches and geomechanical data indicate that effective oriented fracturing stimulation treatments can be implemented where others have failed or unacceptable production changes occurred. The technique can be selcctively applied to: I ) A "smart completion" approach can be implemented; zone determination. design and placement of perforations are based on detailed geomechanical description. 2) Perforations are placed were they are needed the most based on input from the geomechanical model, fully accounting for the formation mechanical properties, 3) Methods to obtain principle stresses to determine optimum phasing with the preferred fracture plane, 4) More efficient placement of fracture stimulation treatments optimizing fracture geometry and treatment volumes. Based on a detailed geomechanical model an effective perforation strategy can be implemented to ensure vertical coverage and proper placement of hydraulic fractures. The advantage of such approach reflects in the improved efficiency of the perforating/fracturing strategies, minimization of treatment failures, treatment design/redesign and the significant impact on production optimization. Recommendations for strategic placement of perforations (density and phasing) and the mechanics for fracture initiation from vertical, deviated and horizontal wellbores are also discussed.

There is an ever-increasing use of variable speed drives in submersible pump applications. However with all new applications new problems can be encountered. The long cable lengths associated with submersible pump equipment have limited the effectiveness of variable speed drives. Many drives have to use external filters, inductors and conditioners to keep from damaging the cable and motor. The extra costs associated with this equipment, as well as the custom use, limit the overall effectiveness. VSG (Variable Sine-wave Generation) technology has been developed to overcome these limitations, as well as providing the user all the flexibility that initially attracted them to Variable Speed Drives.

Beam pumping systems are the most commonly applied world wide artificial lift method. This paper reviews many of the concerns that operators face when using the sucker rod pumping system. The beam pump concerns are introduced with a review of the advantages/disadvantages of the system.

The Dynapump is a means of artificial lift that has been gaining recognition in West Texas and Eastern New Mexico over the past two years. The Dynapump is a hydraulic, ultra long stroke pumping unit that has heavy lift capabilities. The use of solid-state electronics and computerization lower energy costs while giving new flexibility to the artificial lift process. The pumping cycle is optimized through consistent feedback of surface and down hole conditions. The DynaPump's capability to independently adjust the speed of the up and down strokes and change stroke lengths during changing operating conditions result in well optimization while reducing surface and down hole maintenance. The result of the DynaPump design and pumping concept results in an overall reduction in artificial lift costs.

Plunger lifts are used widely to remove liquids from gas wells. The Pacemaker plunger is a new approach to this traditional method of artificial lift. Traditional plunger lifts require shut-in time for the plunger to fall and to build pressure to drive the plunger to surface. Shut-in time equates to lost production and forces liquids back into the formation. The Pacemaker normally only requires 5-10 seconds of shut-in time per cycle, and little or no pressure build-up time. The plunger operates as two interdependent pieces. Each fall separately and can do so against significant gas rates. Once on bottom, the ball scales off in a cavity in the piston. Gas velocity then drives both to surface. At the surface a rod in the lubricator separates the ball from the piston, and the next cycle begins. The end result is that the well produces continuously and liquids arc not forced hack into the formation

A study of the requirements for gathering, metering, compressing, processing and the marketing of products from liquid hydrocarbon recovery units is presented. Costs of installations and payout periods are discussed.

Since the cost of producing oil is continually increasing, oil operators have found themselves in a position of having to determine more economical production methods in order to make a profit. One of the first steps in this direction was the dual completion which enabled the operator to produce two zones, isolated from each other, through the same well bore, at the same time. Although the dual completion is not necessarily new, vast improvements have been made both in technique and equipment and a present day dual completion, producing through parallel strings of tubing is quite commonplace. The dual completion therefore provided the basic principle of multizone completions and was the forerunner of triple and quadruple completions. Also, since the economic aspect of the dual completion has been proved, it was felt that further development in technique and equipment would enable operators to produce three or four zones, isolated from each other, through the same well bore, at the same time, thus providing additional economic gains. Although triple completions are not an everyday occurrence they are no longer a novelty and several quadruple completions have been made successfully. It is the purpose of this paper to present several methods by which three or four zones, isolated from each other, may be produced through the same well bore.